1. Storage and operating ambient temperature of 3M mushroom hasp products
- The product should be stored in an environment of 21°C and a relative humidity of 50%
- Before construction, the mushroom buckle and the materials to be fixed should be placed in an environment above 16°C for at least 24 hours
2. Surface cleaning and treatment of the material to be fixed
- Step 1 Clean the surface with isopropyl alcohol
-Step 2 waits 2-3 minutes to make the solvent evaporate completely
- Step 3 Apply a thin layer evenly on the surface of the material in one direction with 3M #94 primer
- Step 4 Let the coating dry for about 5 minutes at room temperature
##The coating surface must be kept free from contamination Dongguan Jixuan
**For rough or rusted surfaces need to be polished before cleaning the above 4 steps
**For wood surface it is recommended to apply a primer first
Notice:
Due to the different surface treatment of the surface of the material to be fixed, the customer should evaluate the primer according to the actual situation
3. Fix mushroom buckles on the ceiling and beams
- Step 1 Tear off the part of the release paper of the adhesive on the back of the buckle
- Step 2 After aligning, attach this part of the exposed adhesive to the substrate
- Step 3 Press the mushroom buckle with your fingers while pulling out the release paper to ensure that the adhesive is in contact with the substrate and remove air bubbles
- Step 4 Apply pressure to the pasted mushrooms with a mushroom-covered (3552 or 3542) roller
- Step 5 Before closing the mushroom buckle, place the material pasted with the mushroom buckle in an environment above 16°C for maintenance
##24 hours to 90% bond strength; 72 hours to 100% bond strength
##It is forbidden to buckle the mushroom first and then paste it
4. Fasten the mushroom buckle to complete the installation
-step 1
After slipping and aligning the material to be fastened, fasten edge by edge to relieve as much stress as possible
##Be careful not to buckle at the same time
##Mushroom snaps from the sticking surface cannot be reused
- After step 2, apply even pressure again to ensure that the mushroom heads are fully engaged
- The product should be stored in an environment of 21°C and a relative humidity of 50%
- Before construction, the mushroom buckle and the materials to be fixed should be placed in an environment above 16°C for at least 24 hours
2. Surface cleaning and treatment of the material to be fixed
- Step 1 Clean the surface with isopropyl alcohol
-Step 2 waits 2-3 minutes to make the solvent evaporate completely
- Step 3 Apply a thin layer evenly on the surface of the material in one direction with 3M #94 primer
- Step 4 Let the coating dry for about 5 minutes at room temperature
##The coating surface must be kept free from contamination Dongguan Jixuan
**For rough or rusted surfaces need to be polished before cleaning the above 4 steps
**For wood surface it is recommended to apply a primer first
Notice:
Due to the different surface treatment of the surface of the material to be fixed, the customer should evaluate the primer according to the actual situation
3. Fix mushroom buckles on the ceiling and beams
- Step 1 Tear off the part of the release paper of the adhesive on the back of the buckle
- Step 2 After aligning, attach this part of the exposed adhesive to the substrate
- Step 3 Press the mushroom buckle with your fingers while pulling out the release paper to ensure that the adhesive is in contact with the substrate and remove air bubbles
- Step 4 Apply pressure to the pasted mushrooms with a mushroom-covered (3552 or 3542) roller
- Step 5 Before closing the mushroom buckle, place the material pasted with the mushroom buckle in an environment above 16°C for maintenance
##24 hours to 90% bond strength; 72 hours to 100% bond strength
##It is forbidden to buckle the mushroom first and then paste it
4. Fasten the mushroom buckle to complete the installation
-step 1
After slipping and aligning the material to be fastened, fasten edge by edge to relieve as much stress as possible
##Be careful not to buckle at the same time
##Mushroom snaps from the sticking surface cannot be reused
- After step 2, apply even pressure again to ensure that the mushroom heads are fully engaged
